 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
| SIZE dH7 mm | NOMINAL TORQUE¹ Tn Nm | OVERRUNNING SPEED² | Dn6 mm | Lmm | Ds mm | FACE | GROOVE | s mm | emm | t mm | WEIGHT kg | |
| max INNERRACE RPM | max OUTERRACE RPM | b mm | t mm | |||||||||
12 15 |
7 19 |
3300 2400 |
5000 3600 |
35 42 |
13 18 |
28 37 |
4 5 |
1.2 1.2 |
1.2 1.2 |
0.6 0.8 |
0.3 0.3 |
0.06 0.11 |
17 20 25 |
28 44 75 |
2300 2100 1700 |
3400 3100 2600 |
47 52 62 |
19 21 24 |
40 42 51 |
5 6 8 |
2.0 1.8 2.0 |
1.2 1.8 2.4 |
0.8 0.8 1 |
0.8 0.8 0.8 |
0.15 0.20 0.40 |
30 35 40 |
150 230 320 |
1400 1200 1100 |
2200 1900 1700 |
72 80 90 |
27 31 33 |
60 70 78 |
10 12 12 |
2.5 3.5 3.5 |
0.6 0.6 1.2 |
1.8 1.8 1.8 |
1 1 1 |
0.55 0.80 0.95 |
45 50 60 |
460 600 1060 |
1000 850 750 |
1600 1350 1050 |
100 110 130 |
36 40 46 |
85 92 110 |
14 14 18 |
3.5 4.5 5.5 |
2.4 1.2 1.2 |
1.8 1.8 2.6 |
1 1 1.5 |
1.40 1.80 2.80 |
70 80 90 |
1360 2000 2550 |
600 550 500 |
950 850 750 |
150 170 190 |
51 58 64 |
125 140 160 |
20 20 20 |
6.5 7.5 8.0 |
2.2 1.2 2.4
|
2.6 2.6 2.6 |
1.5 1.5 2 |
4.20 6.10 8.2 |
100 120 |
4100 6950 |
450 370 |
680 550 |
215 260 |
73 86 |
175 215 |
24 28 |
8.5 10 |
2.4 3.2 |
2.6 3 |
2 2.5 |
12.6 22 |
| 150 | 14300 | 300 | 460 | 320 | 108 | 260 | 32 | 12 | 3.2 | 3 | 2.5 | 42 |
KEYWAYS: PSN 12.PSN 150 TO DIN 6885 PAGE 1,OTHER SIZE PAGE 3 1)T MAX IS 2.5 x NOMINAL TORQUE (Tn)FOR SHORT PERIODS ONLY. 2)THE INDICATED MAXIMUM OVERRUNNING (IDLING) SPEED ARE VALID FOR PRESSURE LUBRICATION ONLY.FOR OIL BATH LUBRICATION 65% OF INDICATED SPEEDS. IF HIGHER SPEEDS ARE REQUIRED OTHER THAN THOSE LISTED PLEASE CONSULT THE ASSAMBLY DIMENSIONS OF CLUTCHES PS ARE IDENTICAL TO THOSE OF BALL-BEARING SIZES SERIES 62. DRIVE TO THE INNER RACE IS TRANSMITTED BY A KEY WAY AND TO THE OUTER RACE BY A PRESS FIT. WE RECOMMEND THE FOLLOWING LIMITS: SHAFT Dn6 OR j6 BORE DH7 OR J7 |
THIS TYPE OF FREEWHEEL DONOT HAVE THE BEARINGS,HENCE THE OUTER AND INNER RACES MUST BE PRECISELY CENTERED AND ALIGNED WITH RESPECT TO EACH OTHER BY PROVIDING EXTERNAL BEARING SUPPORT. WHILE INSTALLING ,A CARE SHOULDE BE TAKEN THAT THERE IS NO RELATIVE AXIAL TORCE BETWEEN INNER AND OUTER RACES OF FREEWHEEL.PRESS IN AND REMOVEL OF INNER AND OUTER RACE SHOULD BE DONE SIMULTANEOUSLY. FOR INDEXING APPLICATIONS. FREEWHEEL CAN BE SUPPLIED WITH STRONGER 'V' OR 'VV' SPRINGS.THE BEST INDEXING ACCURACY IS REACHED BY USING LUBRICATING OILS WITH A LOW VISCOSITY OF ABOUT 12 mm²/sec AT OPERATING TEMPERATURE. |
| wiperdrive© copyright. 2002 |