 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
| SIZE dH2 mm |
Nominal Torque¹ TN Nm |
OVERRUNNING SPEED² | Dr6 mm | Lmm | S mm |
e mm |
f mm | Weight kg |
|
| max Innerface RPM |
max Outerface RPM | ||||||||
| 10 | 4.5 | 3500 | 5200 | 30 | 9 | 0.6 | 0.6 | 0.3 | 0.03 |
12 15 20 |
7.5 8.5 24 |
3200 2800 2200 |
4800 4300 3300 |
32 35 47 |
10 11 14 |
0.6 1.2 1.2 |
0.6 0.6 0.8 |
0.3 0.3 0.8 |
0.04 0.05 0.12 |
25 30 35 |
35 56 90 |
1900 1600 1300 |
2900 2400 200 |
52 62 72 |
15 16 17 |
1.2 1.6 2.6 |
0.8 0.8 1.8 |
0.8 1 1 |
0.14 0.22 0.31 |
40 45 50 |
115 130 140 |
1200 1000 950 |
1800 1600 1500 |
80 85 90 |
18 19 20 |
1.6 2.6 2.6 |
1.8 1.8 1.8 |
1 1 1 |
0.39 0.44 0.49 |
55 60 80 |
190 300 580 |
800 700 600 |
1300 1100 900 |
100 110 140 |
21 22 26 |
2.6 1.6 2.6 |
2.7 2.7 2.7 |
1 1.5 1.5 |
0.66 0.81 1.41
|
KEYWAYS: PS 10.PS 12 TO DIN 6885 PAGE 1,OTHER SIZE PAGE 3 1)T MAX IS 2.5 x NOMINAL TORQUE (Tn)FOR SHORT PERIODS ONLY. 2)THE INDICATED MAXIMUM OVERRUNNING (IDLING) SPEED ARE VALID FOR PRESSURE LUBRICATION ONLY.FOR OIL BATH LUBRICATION 65% OF INDICATED SPEEDS. IF HIGHER SPEEDS ARE REQUIRED OTHER THAN THOSE LISTED PLEASE CONSULT THE ASSAMBLY DIMENSIONS OF CLUTCHES PS ARE IDENTICAL TO THOSE OF BALL-BEARING SIZES SERIES 62. DRIVE TO THE INNER RACE IS TRANSMITTED BY A KEY WAY AND TO THE OUTER RACE BY A PRESS FIT. WE RECOMMEND THE FOLLOWING LIMITS: SHAFT Dn6 OR j6 BORE DH7 OR J7 |
THIS TYPE OF FREEWHEEL DONOT HAVE THE BEARINGS,HENCE THE OUTER AND INNER RACES MUST BE PRECISELY CENTERED AND ALIGNED WITH RESPECT TO EACH OTHER BY PROVIDING EXTERNAL BEARING SUPPORT. WHILE INSTALLING ,A CARE SHOULDE BE TAKEN THAT THERE IS NO RELATIVE AXIAL TORCE BETWEEN INNER AND OUTER RACES OF FREEWHEEL.PRESS IN AND REMOVEL OF INNER AND OUTER RACE SHOULD BE DONE SIMULTANEOUSLY. FOR INDEXING APPLICATIONS. FREEWHEEL CAN BE SUPPLIED WITH STRONGER 'V' OR 'VV' SPRINGS.THE BEST INDEXING ACCURACY IS REACHED BY USING LUBRICATING OILS WITH A LOW VISCOSITY OF ABOUT 12 mm²/sec AT OPERATING TEMPERATURE. |
| wiperdrive© copyright. 2002 |